How do you attach framing to concrete?

Quote from the video:
Quote from Youtube video: So the method that I use is very simple and relatively. Quick. So I basically have a hammer drill right here and on the hammer drill is a drill bit that can drill through both wood and concrete.

How do you frame an overhead garage door opening?





Quote from the video:
Quote from Youtube video: On each side. So if the garage door is 16-foot wide. This would need to be a half inch smaller.

How do you attach pressure treated wood to concrete?

Quote from the video:
Quote from Youtube video: Move it and take two nails and put them side-by-side. And begin to drive them into the wood. Right down into the hole into the concrete.

How do you finish a garage door opening?

Quote from the video:
Quote from Youtube video: So let's go ahead and start with the top piece. And wrap the inside of the opening. Using this piece of pvc board first thing you need to do is get a measurement from the inside of the opening.

What should I put between wood and concrete?

Anyplace where wood meets the ground or concrete, the lumber must be pressure treated. For additional moisture protection, a gasket or strip of closed-cell foam can be installed between the concrete foundation and the sill plate.

How do you attach a wood frame to a concrete foundation?





Quote from the video:
Quote from Youtube video: We do use mechanical fasteners to attach the sip to the timber frame. And from the sip into the first floor platform. The eye joists are actually also screwed into the sill.

What size header do I need for a 12 foot garage door?

The header itself should be nine inches wider than the door. The rough opening’s width should be three inches longer than the door, measured between the left and right edges. So, in a 12-foot wide garage door, the rough opening will be 15 inches wide.

What do you use for garage door headers?

STRONG AND STABLE, GLULAM IS HIGHLY SUITABLE FOR CREATING LONG, STRAIGHT TWO- AND THREE-CAR OPENINGS. Glulam beams‘ ability to span long distances, their dimensional stability, and cost-competitive value makes them an ideal option for garage door headers, particularly for larger two- and three-car openings.

What size header do I need for a 16 foot garage door?

16 foot garage door header size:– as per general thumb rule and guidelines, for a 16 foot garage door, header made of lvl should be 3-1.75×11-7/8 in size, in which 12 inches deep and 5.25 inches width, thus you will need something like triple- 1.75×11 7/8 or 5.25×11- 7/8 lvl header for a 16 foot garage door.

How do you frame a door opening?



Quote from the video:
Quote from Youtube video: Now with your pre hung doors dimensions in mind mark the location of the king studs with an axe and mark the supporting Jack studs with an O on either side of the rough. Opening.

How do you wrap a garage door jamb?

Quote from the video:
Quote from Youtube video: From the inside face of the jamb to the other side along the header. With your jam cover face up on the saw and a block of wood under the jamb cover for support.

How do you frame a garage?

Quote from the video:
Quote from Youtube video: The goal of this is to create an air gap between the outside and the inside of the building now in our case we aren't insulating the building so it's not quite as critical.

Can you attach wood directly to concrete?



Wood can be attached directly to interior concrete using screws, screws with anchors, anchor bolts, nails, or adhesives. There are a variety of different screw-down fasteners, but all require a predrilled hole. Some require anchors inserted into the concrete, and others bite and grip the edges of the hole.

How do you seal a joint between concrete and wood?

I recommend using an exterior silicone formulation for concrete or a high-quality polyurethane sealant. Both will stick well to the wood and the concrete. Acoustical sealant is a better, albeit slightly more expensive, option. Caulk often works best at a slab-wall transition.

Can you put wood directly on concrete?

Can you put wood directly on concrete? Yes, you can put wood directly on concrete.

What should I put between 2×4 and concrete?

Quote from the video:
Quote from Youtube video: Makes a tape called wig love and this is a particularly good choice wherever we're sticking to concrete. This is going to stick without a primer although certainly we could use a primer.

Does concrete eat wood?



With concrete holding the moisture against the wood, wood has no chance and will eventually lose the battle. Now you don’t have to lose all hope because it’s for certain that the concrete around the post will crack, therefore making it easy to pull out when it starts to rot.

How do you attach timber to concrete?

Quote from the video:
Quote from Youtube video: And basically same idea you drill through your wood product down into the concrete. You and you pull the plastic anchor out the insert I should say hammer.

How do you anchor a 2×4 to concrete?

Quote from the video:
Quote from Youtube video: So instead of sitting there drilling for an hour and a half we're gonna use our ram. Set. Again it is super fun to use and it is super super quick now what i usually do is tack the wall with one nail.

How do I anchor a 2×4 to a concrete wall?

Quote from the video:
Quote from Youtube video: The pilot hole in the wood. I'm going to drill into the concrete. Using this concrete drill bit now the concrete drill bit is just slightly smaller than the thickness of the tapcon concrete screw.