What is the round hole in my basement floor?
Weep holes are drilled in the concrete blocks at the lowest level. Once the block has been drilled, water exits at the holes and flows directly into the drainage system. Weep holes have the added benefit of helping alleviate pressure on your foundation walls.
How do you fix a hole in a cement floor?
- Using a Chisel, Make the Crack Wider at the Bottom than the Top. …
- Clean Out the Debris with a Stiff Fiber or Wire Brush. …
- Fill the Crack with Patching Mix (also know as Vinyl Concrete) …
- Address Any Pop-Outs. …
- Wet the Surface and Apply a Concrete Bonding Agent. …
- Pack a Small Amount of Anchoring Cement into the Hole.
- Step 1: Use a hammer and a cold chisel to level the bottom of the hole. …
- Step 2: Brush on a concrete bonding liquid. …
- Step 3: While the bonding agent is still tacky, mix the concrete. …
- Step 4: Level the patch.
- Clean the surface of the damaged area by removing any loose material such as dirt, oil, or grease and unsound or flaking concrete. …
- Scrub and clean the surface of the repair area with a stiff bristle brush.
- Step 1: Clean out the hole and make sure that it is free of any loose debris, dust, or dirt. …
- Step 2 (Optional): For a stronger bond between the new concrete and the existing cinderblock/concrete, apply a bonding agent. …
- Step 3: Mix up your concrete repair mortar to a ‘clay’ consistency and apply it to the hole.
- Remove the snap tie from the wall, wire brush the surface of the concrete.
- For holes bigger than an 1/8″ , fill with Waterprlug Hydraulic cement. Allow the Waterplug to set for 30 minutes.
- Brush on a heavy coat of Epoxy Waterproofer over the Waterplug and overlap 1″ all the way around the patch.
How do I fill a hole in my basement floor?
How to fill a Large Hole with Concrete
How do I repair a hole in my foundation?
Quote from the video:
So to apply the cement i just put on some surgical gloves. And then grabbed the cement handful by handful. And applied it to the hole in the foundation.
What is the hole in the basement called?
The sump pit (also known as sump, sump basin, or sump well) is a water collection hole in the floor of your basement or crawlspace. It is very common for homes in areas that get regular rain-fall or have high water tables.
How do you repair a hole in a concrete basement floor?
Quote from the video:
Let's get started the deep fill repair mortar is a two-part product containing an aggregate. And a pre-mixed tin of resin and curing agent make a well in the aggregate.
How do you repair an old concrete basement floor?
Apply a concrete patch to the crack, making sure there are no gaps or uneven areas. Smooth the patch with a putty knife. If the crack requires a second patch, then wait for the first layer to dry before applying the second coat. Seal the concrete patch and allow it to dry for several days.
What kind of concrete do you use to patch a basement floor?
QUIKRETE Vinyl Concrete Patcher or QUIKRETE Concrete Patching Compound may be used.
How do you fix a small hole in a concrete foundation?
How do I fix a small hole in my basement wall?
Quote from the video:
You can see there from the picture on the bucket you mix it up and you patch. Around the hole or the crack that you have and it will stop the water. Okay. So again that's quikrete hydraulic.
How do you fix a leaky basement wall and floor?
A drain tile system is the most commonly recommended solution for leaky cove joints. This drain is installed underneath your basement floor. It reduces hydrostatic pressure and directs ground water away that would otherwise leak into your basement – like a gutter under your basement.
Can You Use Flex Seal on basement walls?
Flex Seal Liquid is thicker than paint and dries into a strong, rubberized coating. It can also help seal out air, water, and moisture and is chemical and mildew resistant – making it a great choice for your basement walls.
What is a basement rod hole?
Tie rod holes in basement walls are created by the 5/8” rods used to hold the steel forms together during the original foundation pouring of your basement. After the concrete has cured, the rods are disassembled and when they are removed, holes are left that go straight through your foundation.
Why are there holes drilled in my foundation?
A weep hole is a small hole that’s drilled on the base of your foundation wall to provide aeration and an escape route for water. The weep hole also does the following: Improves drainage: Rainwater or moisture that gets into the concrete block or brick cavity needs to escape.
How far apart are rod holes in basement walls?
During the original construction of a lot of homes, small metal rods, called tie rods, are inserted into the concrete form in order to hold the inner and outer forms together, and provide the structure with which the concrete can be poured. They are placed around 18 inches apart from one another, sometimes in two rows.
How do you fix a snap tie leak?
Snap Tie Leaks:
