When a heater is too powerful for a home, it will heat up the living spaces so fast that the thermostat will shut the heater off prematurely. All you can do in this case is arrange for a new heating system installation—this time from a qualified professional who will make sure the heater is the right size.
How do you fix a furnace that keeps shutting off?
If your furnace keeps shutting off, check your air vents to see if any of them are closed or blocked in any way. You should keep all your vents open, even in the rooms you don’t use. If your heat exchanger doesn’t get enough air, it can’t transfer enough heat.
What does it mean when your furnace keeps shutting off?
A dirty and clogged furnace air filter will not only prevent proper air filtration, but it will actually obstruct airflow to the heat exchanger. If the heat exchanger gets too hot from lack of airflow, a safety mechanism will shut the furnace off to protect it.
Why does my furnace keep shutting off after a few minutes?
If your furnace turns off after a few minutes, there is a good chance it is caused by a faulty or dirty flame sensor. This vital component is designed to keep an eye on the gas burner. When it cannot sense that burner, the furnace runs then shuts off and starts again. This could be a relatively easy fix.
Can a bad thermostat cause a furnace to short cycle?
Thermostat Troubles Can Cause Short Cycling
Your furnace or central air conditioner spends a good amount of energy simply turning on and off, which is why you want yours to run for at least 15 minutes at a time before shutting off.
How do I clean my furnace flame sensor?
Quote from the video:
Quote from Youtube video: So if you have a situation like this what you have 90% of the time is just a dirty flame sensor. So we'll go through the steps on how to clean it. So the right side of the furnace.
Why does my furnace shut off after 15 minutes?
If your air filter is too dirty, it will restrict airflow. Your furnace will then shut off prematurely to avoid overheating. We recommend replacing flat filters once a month, and pleated filters every three months. It’s easy to stay on top of changing your filter by adding a Filter Reminder on your thermostat.
How do you fix a short cycle on a furnace?
A dirty air filter is the most common cause of short-cycling. If your air filter is clogged with dirt, it won’t allow proper air flow to the heat exchanger. That can cause the furnace to overheat and forces the high limit switch to ride to the rescue by shutting the furnace off.
Can a dirty filter shut off furnace?
A dirty furnace filter can cause some serious problems. Namely, it impedes air from flowing properly through your furnace, and can trigger it to shut down. This can result in a colder home.
What do I do if my furnace is short cycling?
If you suspect this is the reason your furnace is short cycling, it is imperative that you contact an HVAV professional to repair the unit. Restricted airflow is typically the cause of overheating which may be due to a dirty air filter or interior vents, or because roof exhaust vent is blocked.
How do you know if you have a bad flame sensor?
Signs of a bad flame sensor
Furnace burners turn on but go out after a few seconds. Soot and other debris is covering the end of the sensor (cleaning the flame sensor may fix this issue rather than a flame sensor replacement) Tip of flame sensor is black. Porcelain/sensor casing is cracked.
How do I know if my flame sensor is dirty?
6 Signs of a Malfunctioning Gas Furnace Flame Sensor
- Yellow Burner Flames. Open up or glance through the peephole of your gas furnace to see the color of the flames firing up in the burner. …
- Rusted Flue Lines. …
- High Utility Bills. …
- Water Leaks. …
- Old Age. …
- Constant Thermostat Adjustments.
Where is furnace sensor located?
A furnace flame sensor is a very basic part of your furnace. It’s located on the burner assembly and is just a thin metallic rod. It’s usually bent, and it sits just in front of the pilot flame inside the furnace.
How much does a flame sensor cost for a furnace?
Flame Sensor
It stops your furnace from letting off large amounts of natural gas if it’s not working properly. If the sensor is bad, it won’t be able to sense heat and will turn the furnace off. The average cost to repair or replace a flame sensor is between $75–$200.
What does a heat sensor look like in a furnace?
It will look like a thin metallic rod and is set in front of the pilot flame on the interior of your furnace. Both of these parts can be located inside of the burner assembly of your furnace which is typically in the bottom of your furnace. Having a dirty flame sensor can result in your furnace not starting.
How long do furnaces usually last?
15 to 20 years
A well-maintained furnace can last at least 15 to 20 years, but completing annual maintenance and being diligent with repairs can extend its life even longer.
What is the most reliable furnace brand?
Best Furnace Brands
- American Standard Furnaces.
- Amana Gas Furnaces.
- Bryant Furnaces.
- Carrier Furnace Units.
- Daikin Furnaces.
- Goodman Gas Furnaces.
- Lennox Furnace Units.
- Rheem Furnaces.
How much is a new furnace for a 2000 square foot home?
The average cost range for purchasing and installing a gas furnace designed to heat a 2,000-square-foot home with a 97% efficiency rating ranges from $4,000 to $8,000, with most homeowners spending around $6,000 total on a high-efficiency gas furnace replacement in a 2,000 sq. ft.
