Why won’t my washing machine spin with a small load?

An imbalanced drum is a common reason for your machine not spinning. The easiest way to avoid an imbalanced drum is by making sure you don’t overload your washing machine, or if you have one large piece of laundry, add smaller pieces to balance out the load. You may also need to check that your machine is level.

Why is my washing machine not spinning at full speed?





If lint or debris has gotten into the water level hose, then the washer may not spin fast. Clean the debris from the hose by blowing on the hose or tapping it on the side. To check the water level switch, go to the back of the washer and locate the back end of the water level hose.

How do you fix a washing machine spin cycle?

If your washer seems to complete all of its cycles but won’t spin:

  1. Check to see if the clothes have jammed or are unbalanced in the drum. …
  2. Check the lid switch and the tab on the lid that strikes it. …
  3. Check the machines’ drive belt. …
  4. There may be a problem with the controls; in this case, call an appliance repair person.


Why does my washer not spin clothes?

The most likely culprit for a washer that spins but still turns out soaked clothing is a drain hose problem. It could be clogged, kinked, or even positioned incorrectly if you had to remove the drain tube to make another repair already.

How do I get my washing machine to spin only?





Quote from the video:
Quote from Youtube video: Turn the unit on and without touching the selector dial move to the spin speed selection button from there press the button until you see your desired spin speed highlighted.

How do I just do a spin cycle on my LG washer?

To activate the spin only feature on your LG top load washer, press the Special Use selection button. And choose spin only. At this time selected the desired spin speed by pressing a spin speed selection button. Note that the no spin option is not available for top-load washers.

How do I change the settings on my LG washing machine?

Press the Power button. – The lights around the cycle selector knob will illuminate and a chime will sound. Turn the cycle selector knob to the desired cycle. – The optimum default cycle settings are automatically set according to the wash cycle.

How do I reset my LG washer?

A washing machine is reset by pressing power off/on button on the control panel & disconnecting it from power board for a few minutes. Reconnect and switch on again. it can be completely cleared with all of the settings renewed.

Does my LG washer have a reset button?



Washer Needs Hard Reset



If your LG washing machine won’t start, try doing a hard reset on the unit. To perform a reset, start by unplugging your washer. Then, press and hold the power button for 5 seconds. Do the same with the play button.

What do you do when your LG washer wont spin?

Quote from the video:
Quote from Youtube video: Next you want to take your multimeter. And turn it on to volts ac. And see if you get between 140 150 volts between the three terminals if you do not receive any voltage your control board has.

How do you do a factory reset on a washing machine?

If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.

Can you reset a washing machine by unplugging it?



To reset your washing machine, unplug it from the power outlet. Then, plug the washer cord back into the wall. Finally, open and close the washing machine door six times to send the reset signal to the system components.

How do I fix the spin cycle on my Samsung washer?

What to do when Samsung washing machine does not spin

  1. Make sure the washer is level and adjust the leveling legs if needed.
  2. Open the door and redistribute the washing more evenly around the drum.
  3. Check that the drum is not over or under-loaded. …
  4. Refer to the user guide to check the cycle selected. …
  5. Open the debris filter.