Why am I not getting gas to my gas fireplace?
The thermocouple is a temperature sensor between the gas valve and the pilot light, and it will generate the electricity to ignite the gas when necessary. If the thermocouple is not screwed in properly, the fireplace won’t work. Check to make sure it is screwed in properly and placed correctly.
How do you test a gas fireplace gas valve?
Quote from the video:
Quote from Youtube video: Completely light the pilot. Turn the gas knob to the on position. Turn the burner on in a high position check the pressure and record it shut the burner off.
How do you purge the air from a gas fireplace?
Quote from the video:
Quote from Youtube video: It is to walk over shut off your wall switch. Turn your wall switch back on and it'll go through another 45 seconds. You should do that up to three times and that will get rid of the air in the gas.
How do I know if my gas fireplace is getting gas?
With an LPG tank, you will usually have a round valve that you turn counterclockwise to open and a gauge located on top of the tank so you can visually see that you have gas. The fireplace should have an inside valve to control the gas flow, usually inside the access panel at the bottom of the fireplace.
How do I know if my gas fireplace valve is bad?
If there is no change in potential when the main valve is activated, then there is a fault or an interrupter may need to be reset. A very small drop in potential may be a sign that the main control valve needs replacement. A digital multimeter can also be used to test the main control valve.
How does a gas fireplace control valve work?
Gas flows into a series of valves attached to your gas fireplace. The valves are always closed unless something opens it. This prevents gas from flowing into your home when the fireplace is not lit. A device called a thermocouple will hold open the pilot light valve as long as the pilot light is lit.
How do you know if a gas valve is open?
A) located just before the gas meter. This valve, often called the street-side valve, is normally a rectangular nub (Photo 1). When the long side of the nub or handle is parallel to the incoming gas line, it’s open and the gas is flowing. When it’s turned a quarter turn, perpendicular to the incoming pipe, it’s closed.
How do I free a stuck gas valve?
Heres how; First, turn off the gas in the house so you don’t blow yourself up or cause a disaster, loosen the bottom nut, tap the bottom of the plug upward to loosen the tapered plug, remove the tapered plug, lubricate with a special gas valve grease , and re-install the plug, job done.
How do you adjust a gas fireplace valve?
Quote from the video:
Quote from Youtube video: Directly below on the bottom of the valve tree how the valves is installed it's gonna either be on your top or at the bottom. Its exposed it's in your manual it tells you how to adjust. It.
How do I get my gas fireplace to work?
Igniting with a Fireplace Key
- Look over the user manual included with your fireplace. …
- Remove your fireplace’s outer cover. …
- Put a fireplace key into the device’s gas valve knob. …
- Hold a long lighter up to the burner and ignite it. …
- Turn the gas key. …
- Replace the fireplace’s outer cover immediately.
Do gas valves go bad?
If your furnace is not producing heat, a faulty gas valve could be the problem. There are several reasons this valve may stop working properly. The valve itself may have simply worn out or may be damaged due to basement seepage or submersion.
How do you clean a gas fireplace valve?
To clean them, use a good quality glass cleaner. After the logs and the glass door, it is the turn of the gas valve. The gas valve should be cleaned at least once in a year. You can use a soft cloth or towel to wipe and clean the gas valve.
How do I clean the thermocouple on my gas fireplace?
How to Clean a Thermocouple on a Gas Fireplace [3 Steps]
- Step 1: Leave the gas to cool first if it has been burning.
- Step 2: Polish the thermocouple.
- Step 3: Blow it out.
- Step 4: Light the gas.
How do you prime a gas fireplace?
Turn the knob from the “Off” to the “Pilot” position. Push in the pilot knob, which manually sends gas into the system. Push the igniter button once every second until it lights. Depending on how long it’s been since the gas fireplace was last used, ignition may take multiple attempts.
How do I know if my gas valve is open?
When the long side of the nub or handle is parallel to the incoming gas line, it’s open and the gas is flowing. When it’s turned a quarter turn, perpendicular to the incoming pipe, it’s closed.
How do I get my gas fireplace to work?
Igniting with a Fireplace Key
- Look over the user manual included with your fireplace. …
- Remove your fireplace’s outer cover. …
- Put a fireplace key into the device’s gas valve knob. …
- Hold a long lighter up to the burner and ignite it. …
- Turn the gas key. …
- Replace the fireplace’s outer cover immediately.
Which way do you turn a gas valve on a fireplace?
Insert the key back into the key hole to increase or decrease the height of the flame as desired. Turning the key counterclockwise increases the flame and turning it clockwise decreases the flame.
Should the pilot light always be on gas fireplace?
We recommend that you turn off your gas fireplace pilot light seasonally. Turning off your gas fireplace’s pilot light can save a substantial amount of energy and money. It is important to remember that not all gas fireplaces have “standing” pilot light, or, a pilot light that is “always on”.
Does gas still flow when pilot light goes out?
If your pilot light repeatedly goes out, this is a likely culprit. If this flame sensor should fail, gas will continue to flow even after the pilot light has been extinguished, causing a safety hazard and requiring immediate repair.
Should I turn off the pilot light on my gas fireplace in the summer?
In general, we suggest homeowners turn the gas pilot light off for the spring and summer months, but if you prefer to keep it on, you likely won’t notice any significant changes in your monthly energy bills or home comfort.
