How do I connect flex duct to trunk line?
Quote from the video:
Quote from Youtube video: And when that handle stick it up mark that tape work that tape over that handle. Until it pushes through iced. Up okay now when that handle pushing through you're going to want to bend it.
What is the disadvantage of flex duct?
The downside of flex ducting is that it is considered temporary with an acknowledged lifespan of only about 15 years. Another major disadvantage is that they are a little too flexible, so they are often incorrectly installed. And with greater friction than metal ducts, proper sizing is critical.
What is the main problem with flex duct?
Too often, flex ducts are not installed properly, and they end up kinked, bunched up, undersized, or sagging. These issues can cause increased resistance in the duct system, resulting in too little airflow reaching a building’s heating and cooling equipment.
Can you use flex duct for a return?
Yes, you can use flex ducts for your return air. However, to maximize its usefulness, it needs to conform to technical specifications such as its insulation rating, pressure checks, dust filters, duct sizing and placement, and lastly, the installation requirements.
Is flex duct better than hard duct?
Flex ducts are better for existing trunk-and-branch heating and cooling systems. This is because they’re more versatile and flexible. Metal ducts are more rigid due to the nature of steel, making them ideal to build an entire HVAC system.
How long can you run flex duct?
5 feet
An International Association of Plumbing and Mechanical Officials committee has approved a change to the group’s Uniform Mechanical Code, limiting the use of flexible ductwork to 5 feet or shorter runs. Flex duct manufacturers oppose the limitation.
Does Flex duct reduce airflow?
Since flex duct, by definition, is flexible, it often flexes in ways we don’t want it to. The result is poor airflow and ineffective HVAC systems.
Is Flexible ducting any good?
Flexible ductwork is made of a thin, pliable material. Not only does this make it less durable than metal, but it also means that flexible ducts are more likely to become damaged in the short term. It’s difficult to install the material without damaging it, as rips and tears can happen very easily.
Is flex duct waterproof?
FlexClad®, designed specifically for HVAC ductwork and piping, is a water and weather-resistant, pre-fabricated, self-adhering, sheet-type protective membrane. The top surface is UV-resistant embossed aluminum that can be left exposed indefinitely, reflects heat and can aid in reducing energy costs.
Can you use flex duct in crawlspace?
Flex duct is commonly used in crawl spaces. That said it is vulnerable to punctures, animals and other hazards. Animals have no particular reason the chew the ducts, but sometimes they will anyway. Flex duct is cheaper to install than hard duct, and (at least initially) it is easier to make it not leak.
Does Flex duct sweat?
Flex ducts themselves do not sweat, however if the connection points are not sealed correctly and duct leakage is occurring then you can get sweating at those points. The good news is with a flex duct system we can either hand seal the connection points or perform an Aeroseal to stop the water.
Can I replace metal duct with flexible?
Metal duct can still be found in many older homes, but flexible duct is more prevalent in newer homes. Both work well. Still, should you decide to change from metal to flexible duct, don’t waste money on an HVAC contractor. It’s a time-consuming job, but definitely one you can do yourself.
How often should flexible ductwork be replaced?
“If your ductwork is over 15 years old, you probably should replace it. Ductwork has a maximum lifespan of 20-25 years. By 15 years, however, it begins to deteriorate, significantly reducing your HVAC system’s efficiency, so replacement is the prudent option.”
Is fiberglass ductwork safe?
Fiberglass, at a minimum, is an acute physical irritant to the skin, eyes, and upper respiratory tract. While no long-term health effects should occur from touching fiberglass.
How long does fiberglass ductwork last?
Ducts are designed to last for about 10-15 years on average. They are made from a combination of materials such as fiberglass and plastic. At some point, these ducts will get damaged. The sooner you see signs of damage and do something about it, the better.
Can you make duct work out of foam board?
Rigid foam board ducts can be installed during new home construction or a remodeling project. You can build ducts from rigid foam board to serve as the distribution system to circulate heated or cooled air in your house.
