The solution is fairly simple. Cut the copper tubing about a foot from the floor and install an inline valve. Use a compression coupler type valve and run the remainder with plastic tubing. Food grade 1/4″ plastic tubing will fit well on a 1/4″ compression or graduated/clamp fitting.
How do you install a shut off valve on an existing water line?
Quote from the video:
Quote from Youtube video: So you want to take the compression nut slide it on you're going to slide the brass washer in place like that back on there now we're going to take our shutoff valve.
Do you need a shut off valve behind the fridge?
If it’s time for refrigerator repair or replacement, you need to find the refrigerator water line shut-off valve. There’s no need to shut off the water to the entire kitchen, which can be an inconvenience for you and the family.
How do I connect my PEX to my refrigerator?
Quote from the video:
Quote from Youtube video: It's made so it'll slide on to half-inch copper or on to pecs the plastic PEX lines. Either way so it'll work on either one of them and this particular valve is made by push and connect.
How do you install a shut off valve on an ice maker?
Quote from the video:
Quote from Youtube video: Up another icemaker we'll just pull this off hook another piece of the longer piece of the quarter-inch line up and go ahead and to our refrigerator.
How do you install a shut off valve on an existing copper water line?
Quote from the video:
Quote from Youtube video: We're going to put the ferrule over the top of it and make sure the ferrule slides all the way down the valve then sits on top of that and you want to make sure that the valve is all the way.
How do you install a PEX shut off valve?
Quote from the video:
Quote from Youtube video: Cut the PEX tube. So the end is square. And free of any burrs or damage or buildup on the surface. Next slide the crimp ring over the tube.
Can you shut off a saddle valve?
Saddle valves are self-tapping devices. Once mounted on a line, with the included rubber seal in place, all that is required is to turn the valve clockwise until it pierces the water line. When the valve handle can no longer be turned, it is done tapping the pipe. Turning the handle counter-clockwise opens the valve.
What is a saddle valve used for?
A saddle valve is a plumbing device that can be used to add an additional water supply line from an existing pipe. It’s called a saddle valve because it mounts on top of the host pipe that it is tapping into.
Should you turn off ice maker when you turn off water?
If your icemaker will not be used for some time (vacation, storage, etc.), we recommend that you shut off the water supply to the refrigerator and turn off the icemaker. If you turn off the water supply, make sure you also turn off the icemaker. Feeler Arm icemakers: The on/off switch is built into wire feeler arm.
What can I use instead of a saddle valve?
A similarly DIY-friendly but more reliable alternative to a saddle valve is a push-fit tee connector designed for ice makers and water dispensers. You install these by cutting out a short section of pipe and installing the tee right into the water line, then adding the small supply line leading to the appliance.
How do you disconnect a refrigerator water line without a valve?
Quote from the video:
Quote from Youtube video: And channel locks you guys usually it's probably you probably just need two channel locks i didn't have two on me right away so i just took a pipe wrench.
How do you install a saddle valve?
Quote from the video:
Quote from Youtube video: And this is self piercing it has a needle valve that is going to cut its own hole into the copper tubing. And then as we unscrew this allow the flow of water to go into our humidifier.
What is a saddle valve for a refrigerator?
The shut-off water valve (also called a saddle valve) is part of the household plumbing. It controls the flow of water from the plumbing to the refrigerator.
Are saddle valves legal?
Answer. Most state and local codes prohibit the use of a saddle valve, also known as a piercing saddle valve, saddle tap or needle valve, consisting of a clamp that punctures a hole in an existing water intake pipe. It is a shortcut used instead of installing a more permanent and secure connection.
How do you install a non piercing saddle valve?
Quote from the video:
Quote from Youtube video: The sample the settle melt like it's laid out here little rubber piece fits the channel of the pipe hug the pipe the the actual saddle valve is going to get inserted. Into the saddle. And twist.
How do you put a saddle valve on a PVC pipe?
Quote from the video:
Quote from Youtube video: And push it inside the saddle valve here with the needle. Open who's gonna feed that needle into the hole. Should feel like kind of make a connection here oh there's more going down my sleeve.
Will a saddle valve work on galvanized pipe?
When installing a saddle valve on galvanized pipe, shut off the water, drain the p[ipe, then drill a hole in the pipe. One of the easiest plumbing installations is self piercing saddle valves. It is possible to install a saddle valve on a fully pressurized copper pipe.
