Where is my refrigerator water line shut off valve?

The shut-off valve is usually located under the kitchen sink, in the basement, in a crawl space or in the cabinet next to the refrigerator. There will be a small 1/4 inch copper line attached to the cold water supply line using a saddle valve (t-valve).

How do you disconnect a refrigerator water line without a valve?

Quote from the video:
Quote from Youtube video: And channel locks you guys usually it's probably you probably just need two channel locks i didn't have two on me right away so i just took a pipe wrench.

Can I use fridge without water line?

Water Lines Aren’t Required

Although refrigerators with water lines are popular, they aren’t necessary. There are several reasons why consumers intentionally look for a refrigerator without a water line. First, not having a water line, water dispenser or ice maker eliminates problems like leaks or performance issues.

How do you install a refrigerator water valve?


  1. Turn off the Water. Locate the fixture shutoff valve on the cold water supply line under the kitchen sink. …
  2. Disconnect the Faucet Water Line. …
  3. Connect the Tee Adapter. …
  4. Connect the Faucet and Refrigerator Supply Tubes. …
  5. Connect the Supply Tube to the Refrigerator. …
  6. Turn on the Water.

How do I disconnect the water to my fridge?

Quote from the video:
Quote from Youtube video: In as you're pulling this pipe out. So what you could do is kind of pull it first on it. And you see that gap. Take your other fingers. And press that all the way back down to where it's snug.

Do I need to turn off water to replace refrigerator filter?

Yes, you can replace the filter without shutting off the water supply.

How do I turn off the water to my Frigidaire refrigerator?

Quote from the video:
Quote from Youtube video: And you've got to turn it 90 degrees to turn it off or to stop the water from flowing. And then you turn it parallel. With your pipe to float. So the water will flow through to your refrigerator.

Should you turn off ice maker when you turn off water?

If your icemaker will not be used for some time (vacation, storage, etc.), we recommend that you shut off the water supply to the refrigerator and turn off the icemaker. If you turn off the water supply, make sure you also turn off the icemaker. Feeler Arm icemakers: The on/off switch is built into wire feeler arm.

Can you shut off a saddle valve?

Saddle valves are self-tapping devices. Once mounted on a line, with the included rubber seal in place, all that is required is to turn the valve clockwise until it pierces the water line. When the valve handle can no longer be turned, it is done tapping the pipe. Turning the handle counter-clockwise opens the valve.

Where is the water inlet valve on a refrigerator?

The water inlet valve is an electronically operated device that connects the household water supply to your fridge if you have an icemaker and/or water dispenser. This valve is usually located at the back of the fridge near the bottom. It supplies water to the dispenser and water the icemaker.

How do you install a shut off valve on an existing water line?

Quote from the video:
Quote from Youtube video: So you want to take the compression nut slide it on you're going to slide the brass washer in place like that back on there now we're going to take our shutoff valve.

What can I use instead of a saddle valve?

A similarly DIY-friendly but more reliable alternative to a saddle valve is a push-fit tee connector designed for ice makers and water dispensers. You install these by cutting out a short section of pipe and installing the tee right into the water line, then adding the small supply line leading to the appliance.

Is a saddle valve safe?

They’ve proven to be reliable, but they’re far more expensive than traditional copper fittings. The most commonly known push fittings are made by SharkBite®, but there are several other ones available, such as PDQ™ and Blue Hawk.

How do you install a saddle valve on a refrigerator?

Quote from the video:
Quote from Youtube video: The supply we then move it over. And insert it into our saddle valve and tighten it with our adjustable range after we make sure that the compression fitting connection you just made is good pierce.

What is a saddle valve for a refrigerator?

The shut-off water valve (also called a saddle valve) is part of the household plumbing. It controls the flow of water from the plumbing to the refrigerator.

Where is the saddle valve located?

The saddle valve is usually installed on a nearby pipe under the kitchen sink but is sometimes installed in the basement. Locating the water shut-off valve to the refrigerator can often be the most difficult part of turning on and shutting off the water supply.

How do I know if a saddle valve is open?

Self-tapping devices are called saddle valves. Once mounted on a line, all you need to do is turn the valve clockwise until it pierces the water line. tapping the pipe is done when the valve handle is not turned. The valve is opened by turning the handle counter-clockwise.

How do you attach a hose to a saddle valve?

  1. Locate the copper tubing of your water. …
  2. Slide the saddle valve over the copper. …
  3. Tighten the screws with equal pressure on. …
  4. Connect the water hose to the female. …
  5. Turn the saddle valve handle as far as you. …
  6. Turn the saddle valve handle counter-
  7. Are saddle valves legal?

    Answer. Most state and local codes prohibit the use of a saddle valve, also known as a piercing saddle valve, saddle tap or needle valve, consisting of a clamp that punctures a hole in an existing water intake pipe. It is a shortcut used instead of installing a more permanent and secure connection.

    How do you install a piercing valve?

    Quote from the video:
    Quote from Youtube video: We'll put the screws in place put in the screws. I'm going to have it in this position. And then just sort of snug them up and then i'll be able to spin. This spin it around to the other.