Do LED drivers need to be accessible?
Firstly, the LED driver should be placed in a ventilated space and an access route should be made available for common maintenance purposes. Additionally, the IP, or International Protection Code or rating of the driver must be considered before finalizing the location for mounting the LED driver.
What is the minimum distance that recessed lighting fixtures must be mounted away from combustible material?
½ inch
8 Recessed Luminaire Clearance. A recessed luminaire that is not identified for contact with insulation should have all recessed parts spaced at least ½ inch from combustible materials.
What is the minimum distance above combustible material that a lighting fixture may be installed?
Rule 30-902 Spacings for Non-IC type luminaires.
This type of Non-IC recessed luminaire must be marked Type Non-IC and its installation must provide at least 13 mm spacing from combustible materials other than at the point of support, and thermal insulation must not be closer than 76 mm from the luminaire.
What term is used to refer to a lighting fixture in the CEC?
OPTICS: A term referring to the components of a light fixture (such as reflectors, refractors, lenses, louvers) or to the light emitting or light-controlling performance of a fixture.
Do LED drivers need ventilation?
LED drivers need to be mounted in a ventilated space. Access to the driver needs to be provided for general maintenance purposes.
How do you hide LED driver in ceiling?
Youtube quote:You use three-quarter inch or larger double-sided foam tape you're going to need to trim it off if you use a half-inch. It should fit right on there. And you won't need to do any trimming.
What is the code for recessed lighting?
NEC 410-8 – Lighting fixtures installed in a clothes closet shall have the following clearances from the defined storage area (see the definition below): 12 inches for surface incandescent fixtures, 6 inches for recessed incandescent fixtures, 6 inches for fluorescent fixtures.
Can LED recessed lights be covered with insulation?
The IC rating determines that it is safe to install recessed lighting in a ceiling with regular insulation such as fiberglass insulation. However, if you’re thinking of using other materials such as spray foam insulation, you might need to consult a contractor you trust.
What is the current Canadian Electrical Code?
The first edition of the Canadian Electrical Code was published in 1927. The current (25th) edition was published in April of 2021.
What is the Ontario Electrical Safety Code?
The Ontario Electrical Safety Code is a provincial regulation that sets safety standards for the installation and maintenance of electrical equipment. It is mainly a technical document aimed at enforcing safety standards.
What section of the CEC sets out requirements for installing light fixtures?
Section 30, as outlined in rule 30-000 Scope, is a supplementary or amendatory section of the code and provides additional and specific requirements for the location, installation, wiring, protection, and control of all lighting equipment.
Where are 3 way switches required in a stairway CEC?
3-way switching is required on stairway lighting when a stairway has four or more risers AND is leading to a finished area or to an outside entrance.
What is the difference between 14 2 wire and 14 3 wire?
Youtube quote:3 what's the difference. Well if you look inside the jacket of a 14 2 wire you will see a black wire a white wire and a bare copper wire that's your hot neutral and ground wire.
How many outlets can be on a 15 amp circuit in Ontario?
Technically, you can have as many outlets on a 15 amp circuit breaker as you want. However, a good rule of thumb is 1 outlet per 1.5 amps, up to 80% of the capacity of the circuit breaker. Therefore, we would suggest a maximum of 8 outlets for a 15 amp circuit.
How many receptacles can be on a 15 amp circuit Canada?
12 outlets
a) 12 outlets for a 15 A branch circuit where the fused switch or circuit breaker is marked for continuous operation at 80%;
Are wire nuts allowed in breaker panel in Canada?
emtnut wrote: Inspectors in Canada will only allow pigtails in panels under certain conditions. ie, on a panel change/upgrade, or modifying an exsisting circuit. For new circuits, they will (can) fail you if you use a wirenut. They really are taboo.
Can bedroom lights and outlets be on the same circuit?
Yes, if you want, you can use separate circuits for your outlets and lights. In this process usually, a 15 amp circuit is used for lighting. For the outlets, you can use a 20 amp one. You can use 12 gauge wires for your lights on both the 20 and 15 amp circuits.
Can you run lights and outlets on the same circuit?
Yes, you can. The average home uses an indoor distribution board that houses the breakers of the majority of circuits in the home. A circuit controlled by a 15A circuit breaker (which a lot of contractors use for general lighting) can also accommodate outlets.
How many LED lights can I put on a 15 amp circuit?
Each CFL or LED bulb typically gives the same amount of light as a 60-watt incandescent bulb while drawing 10 watts or less, which is equivalent to a current draw of 1/12 amp. Thus a 15-amp circuit can safely control 180 or more fixtures that use CFL or LED bulbs.
How many LEDS can be on a 20 amp circuit?
Up to 40 lights can be put on a 20 Amp breaker.
