How do you unscrew a toilet supply line?
Quote from the video:
Quote from Youtube video: The water supply from the toilet. As you see here is the actual shutoff valve here for the toilet and the supply that goes up to the toilet.
How do you remove a water supply coupling nut?
Locate the coupling nut on the underside of the toilet tank. Empty the bucket and place it underneath the water supply line. Use a pair of pliers to just loosen the coupling nut. Then finish loosening the nut with your fingers.
How do you remove a rigid toilet supply line?
Quote from the video:
Quote from Youtube video: This should easily unscrew by hand once the nut becomes loose gently pull the water supply line to the side. Now pull the hard water supply line straight out of the top of the valve.
How do you remove a plumbing hose?
Instead of using a knife, remove the hose with a soldering iron. Just add a plastic cutting tip to it and bend it 90 degrees so it acts like a cutting blade. Then, after letting it heat up, slowly use it to cut down the hose.
How do you replace a plastic toilet supply line?
Quote from the video:
Quote from Youtube video: Turn off your main valve. Sure that you removed or turned off that valve you want to come here you can open it make sure the water comes out. You can see here we're kind of just dripping right now.
How do you change a toilet water shut off valve?
How to Replace a Toilet Shut-Off Valve
- STEP 1: Cut the water supply. …
- STEP 2: Drain the water lines. …
- STEP 3: Disconnect the supply line. …
- STEP 4: Remove the old toilet shut-off valve. …
- STEP 5: Install the new shut-off valve. …
- STEP 6: Attach the toilet supply line. …
- STEP 7: Turn on the water.
How do I remove a toilet mounting nut?
The Bottom Line
- Step 1: Close the water supply line.
- Step 2: Place a towel under the toilet tank.
- Step 3: Take the lid off the top of the tank.
- Step 4: Drain the water from the tank.
- Step 5: Remove the plastic coupling.
- Step 6: Unscrew the nut by turning it clockwise.
How do you replace a toilet coupling nut?
Quote from the video:
Quote from Youtube video: Having any water drain into the plastic bin. Below. Now with an open and adjustable wrench or rib joint pliers unscrew. The lock nut located on the bottom of the ballcock supply valve shank.
How do you remove a stuck plastic nut from a toilet tank?
One of the best ways to remove a difficult lock nut is by using plumber’s grease. Simply apply the plumber’s grease to lubricate the plastic nut, then let it sit for 10 to 15 minutes. Once that has sat for a while, attempt to remove it using your hands or a pair of pliers.
How do you remove a push on hose connector?
Quote from the video:
Quote from Youtube video: Just use a wrench. This is a 3/4 inch line 13/16 wrench just push it on here this is really chewed up but it'll go on the other end too just going to give it a good push on.
How do you disconnect a water line connector?
Quote from the video:
Quote from Youtube video: We press in both the hose and the collar. We hold the collar and pull to remove the hose. If we need to reinstall this hose. We want to cut past where our notches are from where the collar.
How do you remove a cross threaded hose?
The way to remove it is to grind a notch with a dremel tool in the top of the set screw, and then use a flat head screwdriver to back out the set screw. It is very possible that you damaged the threads of your hose fitting by trying to unscrew this device without removing the set screw.
Which way do you unscrew a hose?
Turn the hose collar to the left, or counterclockwise, when you try to remove it. If you have accidentally turned the hose to your right, you may have actually tightened it by mistake.
How do you remove a hose bib stem?
As I recall, you would follow this procedure…
- Turn off the water, so no pressure is found at the valve itself.
- Remove the handle, by unscrewing the small screw in the center. …
- Remove the small nut around the stem.
- Put the handle back on. …
- If the stem will not pull out, you need to pull out the packing around the stem.
How do you replace a hose stem?
Quote from the video:
Quote from Youtube video: So for doing that you turn the water off loosen the bonnet. And back this out. So now the stem comes out completely comes out completely and now you can see this is a Phillips head screw.
How do I remove an old spigot handle?
Squirt a few drops of penetrating oil or spray lubricant into the space between the handle and the valve stem. Wait a few minutes, then tap the handle and try pulling it off.
How do you replace a valve stem on an outside faucet?
Quote from the video:
Quote from Youtube video: And screw it clockwise into place hold the faucet with one hand to stop it from turning and tighten the valve stem assembly with an adjustable wrench.
How do you remove an outside spigot?
Steps for Replacing a Spigot:
- Shut off the water supply.
- Go inside and find the line that goes to the spigot.
- Cut the pipe in an accessible place. …
- Remove the spigot and pull the pipe out.
- Get a measurement for the new pipe connection. …
- Slide the spigot into place.
- Solder the connection using a coupling fitting.
How do you replace a hose spigot handle?
Quote from the video:
Quote from Youtube video: Okay so the first thing we're gonna do is we're gonna grab a screwdriver and we're gonna take off this old one be careful make sure that you're holding this handle you do not want this screw to strip.
