How do you put a Whirlpool dryer in diagnostic mode?
Quote from the video:
Quote from Youtube video: The green circle buttons are the ones that can be used to enter the Diagnostics mode. But make sure to remember which three buttons you press because they will need to be referenced.
How do you fix a Whirlpool gas dryer that won’t heat?
Quote from the video:
Quote from Youtube video: Sure you check that your vent isn't kinked or clogged. If. It is make sure to fix it and clean out the dryer when you replace the fuse.
How do you troubleshoot a Whirlpool dryer?
Quote from the video:
Quote from Youtube video: Happening your motor is probably out or there's a wiring issue going towards the motor.
Why is my Whirlpool gas dryer not drying?
When gas or electric Whirlpool Dryer is not heating up, it usually caused by: Burnt Heating Element or Gas Valve Solenoid, Burnt Thermal Cut-Off Fuse, Defective Cycling Thermostat Or Gas Ignitor, Malfunctioned Flame Sensor.
How do I run a diagnostic test on Whirlpool?
Quote from the video:
Quote from Youtube video: You press the start button this will allow your washing machine to go into the test or diagnostic mode and this will isolate if you're having any issues the water will run the spin cycle will engage.
How do you reset a Whirlpool dryer?
If your Whirlpool dryer displays a “PF” error code, indicating a recent power failure, the dryer will need to be reset and restarted. This is done by pressing “Start” for a few seconds to restart the dryer. If the dryer does not restart automatically, select a new cycle and any options then press “Start” to begin.
Why is my dryer running but not heating?
Common reasons for an electric or gas dryer not heating are a tripped circuit breaker, clogged vent, and no gas flow. Other potential reasons include a faulty thermal fuse and broken heating element.
What can cause a gas dryer to stop heating?
7 Reasons Your Gas Dryer Is Not Heating
- 1 – Faulty Gas Valve Solenoid Coils. These open the gas valves and let gas flow into the burner. …
- 2 – Blown Thermal Fuse. …
- 3 – Faulty Igniter. …
- 4 – Gas Supply To The Dryer. …
- 5 – Defective Flame Sensor. …
- 6 – Faulty High Limit or Cycling Thermostat. …
- 7 – Faulty or Loose Wiring In Gas Dryer.
How do you troubleshoot a gas dryer?
Gas Dryer Troubleshooting Guide
- Make sure the dryer is plugged in.
- Check for a blown fuse or tripped circuit breaker.
- Test the power outlet for voltage.
- Inspect the electrical cord for damage.
- Eliminate use of an extension cord, if any is being used.
- Check the outlet voltage.
- Test the door switch.
- Test the start switch.
What does Whirlpool diagnostic mode do?
The washer’s diagnostic mode can be used to troubleshoot washer problems by viewing logged washer errors, performing an automatic diagnostic cycle, or manually turning on and off different washer parts to test for proper operation.
How do you put a Whirlpool Duet steam dryer in diagnostic mode?
Quote from the video:
Quote from Youtube video: But if you have the standard duet you're going to press extra rinse four times within five seconds if you have the one that.
How do I put my Whirlpool Duet in diagnostic mode?
Quote from the video:
Quote from Youtube video: Hit options and hold hit it four times one. Two three four and then it start your diagnostic mode.
How do you troubleshoot a Whirlpool Duet dryer?
Whirlpool Duet Dryer Will Not Start
- Check the Circuits. Always check that the dryer is receiving the proper amount of 240v current. …
- Check the Door Latch. The dryer will not start if the door latch is malfunctioning. …
- Check the Thermal Fuse. Check to see if the Whirlpool dryer thermal fuse is blown. …
- Check the Start Button.
How do I reset my Whirlpool Duet HT?
Rotate your dial until you have the following three lights illuminated: RINSE, WASH, and STOP. Then turn off your washer and unplug it for ten seconds. When you turn it back on it should be reset. You can run a test load without any clothing to ensure that the reset worked.
How do I find the code on my Whirlpool washer?
Quote from the video:
Quote from Youtube video: Start with the cycle selector knob in this position. Next you need to turn the cycle selector not the way that I'm going to show you one click to the left three clicks to the right.
How do I read a Whirlpool error code?
Quote from the video:
Quote from Youtube video: If your machine is displaying F H that is an input error. It means the machine has a problem filling with water check for a kinked or trapped hose.
What are the Whirlpool error codes?
Error Codes in my Whirlpool Front Load Washer
| Error Code | Error |
|---|---|
| Sud or Sd | There are too many suds in the washing machine. |
| F5 E2 | The door is not locking properly. |
| F7 E1 | Indicates a motor speed sensing error, |
| F8 E1 or LO FL | The washer is sensing a low flow of water. |
