1 Answer
- A reciprocating saw to cut the posts off.
- An angle grinder to cut more of the posts off.
- A powered chisel thing to get rid of some of the concrete that was inside the posts.
- A hammer and lots of effort to fold the remaining parts of the posts down.
How do you remove metal post from concrete?
Use the Jack for Removing Steel Fence Posts
Put the end of the chain on the jack tongue and crank the jack. Keep a close eye on the chain to ensure that it doesn’t slip or move. Once you lift the pole and slab enough, you should have someone help you lift them out of the ground and carry them away.
How do you cut a metal pole in the ground?
- Fit your saw with a carbide blade. …
- Mark a line for your cut using a chisel or the edge of a saw blade.
- Secure the pole. …
- Cut the pole. …
- Smooth the cut edges. …
- Remove any combustible material from your worksite. …
- Set up a box of sand or an extra piece of steel underneath your cutting site to catch the metal slag.
- Use and wear all relevant safety protective equipment and prepare suitable workplace.
- Do not operate tools or machinery that you are not competent and trained to use.
How do you cut galvanized steel post?
To cut the galvanized steel with a circular saw, you need to place the steel tight in one place. You can use clamps to hold the steel or use the bench vice to do your job. Then place the circular saw in the place where you want to cut. Use a 7.5-inch fiber blade to cut your steel pipe.
How do you cut a metal pole at home?
Quote from the video:
Quote from Youtube video: Towards you and start cutting. And allow the saw to do the work. If you push too hard. You'll. Find then it'll bind as well. But it's back and forth even strokes.
How do you remove a metal fence post from the ground without digging?
Saturate the ground around the base of the post with water from a garden hose. Let the water soak in until the ground is muddy. Wiggle the post back and forth to loosen it. Even if it doesn’t move very much, any amount of loosening of the soil around the base will make it easier to remove.
How do you get a post out of the ground?
Quote from the video:
Quote from Youtube video: Use a digging bar if you have hard-packed or rocky. Soil. Then wrap the chain around the concrete. And use the slip hook to latch the chain to itself pull the chain tight.
What is the best tool for cutting metal?
Tin Snips. Like a pair of scissors, tin snips are an inexpensive handheld tool that cuts straight, or if the blade is curved, can cut curves and circles. Tin snips are ideal for cutting soft metals like aluminum and copper, and are especially useful for cutting sheet metal, gutters, metal roofing, and studs.
How do you cut a concrete pole?
Concrete posts can be cut to desired length using a masonary disc on an 5 inch angle grinder.
Can you cut metal fence posts?
Registered. Yes, you can use a Sawzall and get the job done.
What can I use to cut a metal fence post?
Quote from the video:
Quote from Youtube video: Hiya Jim I'm Aiman and this is the Hercules angle grinder. So easiness to cut this post here because it's blocking or password or wheelbarrow to go through. But anyway this Hercules angle grinder is
Can angle grinder cut steel?
Cutting metal, aluminium and steel with an angle grinder
You can use it for all kinds of metal, including bolts, pipes, iron, steel and sheet metal. You’ll need to use an abrasive metal-cutting disc. Secure the disc on the grinder and place the metal on a flat surface.
What can I cut a metal fence with?
Thankfully, your aluminum fence section can be trimmed down with a hacksaw (or any metal blade saw) to just about any width needed. For example, you have a run along the front of your property that is 32′ long to the property line.
How do you cut reinforced concrete fence posts?
Support the post & give a good belt with a lump hammer, should enough to reveal the rebar so you can cut it with your grinder, most likely only two lengths of rebar per post. Best thing to cut them is a Stihl saw or 9″ grinder, can hire for a day or weekend.
Will an angle grinder cut wrought iron?
While you could use a reciprocating saw or even a hacksaw to vigorously slice your way through cast iron, utilizing an angle grinder to swiftly cut segments of cast iron pipe, is a viable option too.
Can wrought iron be cut?
Tools. An oxyacetylene torch or a titanium-coated, high-speed steel saw blade on a hacksaw or right angle grinder can all be used to cut wrought iron. The torch can cut close as long as the rail is attached to concrete or some other nonflammable surface.
How do you cut wrought iron posts?
Quote from the video:
Quote from Youtube video: Option good old hacksaw. Very basic and simple tool most people have if not you can find it in pretty much any home hardware.
Can a Sawzall cut wrought iron?
If you are more comfortable using a reciprocating saw, get some blades for use on cast iron. They will cut wrought iron like butter.
