Why is my air conditioner running outside but not inside?

A jammed or clogged condenser coil could be the cause of your air conditioner running but not dropping temperatures inside. The condenser fan pulls air into the outside device through the condenser coil to extract heat energy from your home while it’s working properly.

Why is my blower not working on my AC unit?





If it is in the air conditioning mode, check for ice around the evaporator coil and on the refrigerant lines at the indoor unit. If the coil froze, the fan could be working but the air wont go through the ice until it melts. If the fan isn’t working, that can cause the coil to freeze.

How do I reset my AC blower?

Locate the reset button on the furnace and press it to reset the furnace. It is usually located inside the blower compartment on the side of the blower motor. Be cautious as the housing may be hot. If the button is popped up, press it down.

Why is my blower fan not working?

If little air is coming through the vents (hot or cold), then it could be because the blower motor for the fan or a switch or resistor that controls fan speed isn’t working. Another cause might be that the electronically controlled “blend doors” that direct air flow are stuck or broken.

How do you unblock a condenser coil?

Quote from the video:
Quote from Youtube video: Clean it and we're going to be using that on this and then what you do is you spray it on there and you let it sit for about 10 to 15 minutes and then you spray it off with the water hose.

How do you unclog an AC drain line?





How to Unclog Your AC Condensate Drain Line

  1. Turn off your air conditioner. …
  2. Remove the cap from the pipe. …
  3. Check to see if there is any debris stuck in the drain. …
  4. Remove any visible debris and retest for proper drainage. …
  5. Pour in Vinegar. …
  6. Replace the drain cap. …
  7. Remove the drain cap.

What causes blower motor failure?

Blower motor breakdown can be the result of anything from old age to failed bearings, high amp draw, electrical failure in the windings, dirt accumulation, and more. “The most common cause is dirt accumulation due to lack of maintenance,” said Tom Beaulieu, president of Bay Area Services Inc.

How do I test my AC blower fan?

Quote from the video:
Quote from Youtube video: And then you put one probe on there and one to the l2. Common neutral bar right here and you should read 120 volts. If you read 120 volts. And your blower motor is not turning on then.

How do I know if my AC blower motor is bad?

Be aware of the following signs and symptoms of a bad AC fan motor.

  1. AC Fan Doesn’t Start. Even though you have the AC turned on, the fan does not start.
  2. AC Fan Doesn’t Stop. …
  3. Slow Rotating Blades. …
  4. Outside Fan Blades Are Still. …
  5. Rattling, Humming, and Buzzing Noises. …
  6. AC Runs Intermittently. …
  7. No Cold Airflow.



Is there a fuse for the blower motor?

Fuse Protection



To protect the blower motor power circuit, a 20-, 25- or 30-amp fuse is usually located in the fuse panel under the dash. The rating of the fuse will depend on the vehicle application and how much power the blower motor requires at full speed.

How do you test a blower motor?

Quote from the video:
Quote from Youtube video: And I just connected it to battery terminal one on a hot one on to the on to the neutral. Basically one on where you would put your red jumper cable one where you would put your black on that.

How do I know if it’s the blower motor or the resistor?



Typically, if the fan will work on some speeds but not on others, the resistor is suspect. Okay, let’s say there’s no melting going on, but your fan doesn’t work on all speeds. Typically, if the fan will work on some speeds but not on others, the resistor is suspect.

Where is a blower motor located?

The blower motor is usually under the dashboard on the passenger side. Blower motors that make loud squeaks or rattling noises may be worn out and on the verge of packing it in, but sometimes those noises are caused by leaves or other debris that can be cleaned out after the motor is removed from the vehicle.