Is a double pole 30 amp breaker 60 amps?

A main breaker is the same as any double breaker in the box, except that it supplies power to each busbar. The answer is no if you want to draw 60 Amps off a 30 Amp double breaker.

How many amps can a 60 amp disconnect handle?


Electrical Product Type Disconnect Non-Fusible
Maximum Amperage (amps) 60 14000.000
NEMA Configuration NEMA 3R 1 Phase
Power Distribution Features No Additional Features 2.7
Returnable 90-Day Air Conditioner

How many amps is a double pole 60?

Compare with similar items

This item Circuit Breaker, Double Pole, 60-Amp, 240-Volt Double-Pole Circuit Breaker, 30A
Current Rating 60 amps 30.0 amps
Item Dimensions 18 x 2 x 3.3 inches 18 x 2 x 3 inches
Mounting Type Plug-In Mount Pole
Number Of Poles 2 2

What size wire do I need for a double pole 60 amp breaker?

Installing a 60-amp double pole breaker is relatively straightforward. Most electricians choose to wire a 60-amp breaker using 4-gauge wire for extra security, but 6-gauge wire can handle the load. Most appliances that draw a current of 60 amps are usually 240 volts and not that standard 120 volts.

Can I put a 30 amp breaker in a 60 amp panel?

No you cannot do that. The circuit breaker is there primarily to protect the conductors from overload. So any conductors connected to your 60A breaker must be conductors rated for 60A even if the load it serves is less than 60A.

What size wire do I need for 60 amps?

60 amp wire size is either 6 AWG or 4 AWG wire (AWG stands for American Wire Gauge; standard wire sizing is the US) for 220V voltage. An amateur will use a 6 AWG wire size for 60 amp 220V. A professional will always use 4 AWG wire size for 60 amp 220V.

How many circuits can you put on a 60 amp sub panel?

Modern 60-amp electrical panels are purpose-built as sub-panels and generally only have 8 to 10 slots available for circuit breakers.

Panel Rating Number of Spaces/Slots Number of Individual Circuits
150 amp 30 60
100 amp 12 24

What wire size do I need to go 100 feet for a 60 amp service to a workshop?

What size wire should I use for a 60 amp subpanel? You can get away with 6 AWG when you have a short run of wire, however, due to voltage drop, if you ever decide you want to go more than 100 feet then a 4 AWG is the size you should choose.

What is a 60 amp breaker used for?

The Square D by Schneider Electric Homeline 60 Amp Two-Pole Circuit Breaker is used for overload and short-circuit protection of your electrical system. This breaker is compatible with Homeline load centers and CSED devices. The ANSI-certified and UL-listed unit is rated for 120/240 VAC and 10,000 AIR.

Can you put a 50 amp breaker in a 60 amp panel?

The 50A breaker will be protecting the wiring to the tub (and internals of the tub). The 60A breaker is protecting the wiring to the subpanel (and its internals). You can do this if you want and you will be perfectly fine.

Can I put a 60 amp breaker in a 100 amp panel?

The main panel’s breaker limits you to 60 Amps because the sub-panel is 100 Amps. You could charge 32 Amps if you are not running the other loads.

Can 8 gauge wire handle 60 amps?

“Twelve-gauge wire is good for 20 amps, 10-gauge wire is good for 30 amps, 8-gauge is good for 40 amps, and 6-gauge is good for 55 amps,” and “The circuit breaker or fuse is always sized to protect the conductor [wire].”

Does a 60 amp sub panel need a main breaker?

Your subpanel does not need a main breaker if it’s in the same building. If it is in an outbuilding, you need a disconnect switch, and the breaker will suffice but its size doen’t matter.

What size breaker do I need for a 60 amp subpanel?

You have to use a #4 conductor to feed a 60 amp circuit.

Is 60 amps enough for a garage?

As for basic lighting or low-load electronic devices, a 50- or 60-amp subpanel in a detached garage may suffice. You’ll likely have to increase the ampacity further if you intend to run heavy machinery or power tools in your garage.

How far can subpanel be from main panel?

The right feet would be between 4.5 to 5 feet.

The cable running from your main panel to the subpanel depends on the amperage rating. For instance, for a 30A panel, use a 10 AWG, three-wire conductor.

Can I add a subpanel to a subpanel?

Can I run a subpanel from a subpanel? Generally speaking, yes. You could put a million subpanels in series, and by itself that wouldn’t be a code violation. The metal conduit can act as the equipment ground so a 4th wire is not required.

How do you run a 60 amp subpanel?

Quote from the video:
Quote from Youtube video: I have installed it's a 60 amp breaker. So I'm feeding a 60 amp subpanel. And one thing to kind of keep in mind and when you're planning all this is breakers protect downstream wires.

How many subpanels can you have?

Even though there is no limit on the number of subpanels that you can add to a circuit, it shouldn’t exceed 160 amps when you’re using a 200 amp main panel. Always follow this guide to install subpanels effectively.

Can you wire a subpanel with 3 wires?

Another way to wire a subpanel was with a three-wire feed; two hots and a neutral, with grounds and neutrals connected together at the subpanel. In this case, the grounds and neutrals have to be connected together.