Unscrew the connector using locking pliers and purchase a cap or plug that will fit it. It’s easy to install the cap — just screw it on. Once it’s tight, turn on the water to make sure it doesn’t leak, then turn the water off again, and you’re ready to plug in the refrigerator and push it back against the wall.
How do you fix a leaky refrigerator water line?
Quote from Youtube video: Using a box cutter or pair of scissors. Cut a straight half inch piece off of the tube. And reconnect ensuring that the tube is firmly pressed into place reattach the grill base.
How do you crimp a refrigerator water line?
Quote from the video:
Quote from Youtube video: And attach it to a saddle valve. And tighten it with an adjustable wrench. Open up the saddle valve and let the water out to flush the line for about five minutes we don't want the stale taste.
Why is my fridge water line leaking?
Why is my fridge water line leaking? This is often a sign the inlet valve is clogged. Debris and food can clog the valve and lead to a drip. The valve will need to be cleaned or replaced.
How do you fix a leaky copper water line on a refrigerator?
Quote from the video:
Quote from Youtube video: After damage pieces removed we're going to take this little piece that comes on your pipe cutter. And put it into the tubes. And return them to the original.
What is a ferrule for fridge?
The ferrule, AKA sleeve or olive, is the part the compresses on to the pipe which makes for a leak free joint. If you use a brass ferrule, you run the chance of it cutting thru the pipe and causing the fitting to leak, this is where most DIYers make a mistake that could potentially lead to a disaster.
How do you put a compression fitting on a refrigerator water line?
Quote from the video:
Quote from Youtube video: Wrench. Remember to orientate the ferrule in the right direction tapirs side towards the like you see here. So insert the tube into the valve.
Can you cap off a saddle valve?
If you don’t want to hassle with removing the saddle AND the tubing coming off the saddle is copper and you just want to permanently but reliably cap it off, cut the copper coming off the saddle at least 6 inches away from the pipe and then solder on a cap rather than use a compression fitting.
Can you patch a refrigerator water line?
If you need to fix a refrigerator water line leak in copper tubing, the steps are basically the same as repairing a plastic water line. Identify the damaged length of line, remove it with a tubing cutter, and replace it with copper tubing secured with brass unions at each end of the fix.
Can you use metal ferrule on plastic tubing?
Grab the brass ferrule between your index finger and thumb and work the ferrule over the plastic tube. The fit will be a little tight, but this is what you want. Work the ferrule approximately 3/4 inch from the cut end. Push the end of the plastic tube into the female compression fitting.
How do you install plastic ferrules?
Quote from the video:
Quote from Youtube video: When you use a PEC supply tube you use a plastic ferrule. So you would put your nut on here followed by a plastic ferrule. And then into your adapter. If that's what you have or into your valve.
Can you use a brass ferrule on plastic tubing?
Brass ferrules are normally used on copper tubing and can cut into the soft plastic supply line.
How do you install ferrule on plastic tubing?
Quote from the video:
Quote from Youtube video: Now into the fitting bringing the nut all the way in and then like before hand tighten until you can't hand tighten anymore once it seats you're going to take your wrench.
Do compression fittings work on plastic pipe?
A compression fitting works in the same way on a plastic pipe as it does on a copper pipe except that you need to put in a liner, which is there to keep the end of the pipe perfectly round.
How do you fix a leaking plastic compression fitting?
Quote from the video:
Quote from Youtube video: You make sure you have a gap in the pipe enough to get fitting in being that it's tight you need as much as you can but not too much that is definitely not cut too big.
Do you use plumbers tape on compression fittings?
Quote from the video:
Quote from Youtube video: And that creates a watertight seal. So you should never need to put any PTFE tip on a compression fitting.
How do you seal compression fittings?
Quote from the video:
Quote from Youtube video: Snap that off make sure it's all neat. Okay like so all neat. And if you notice i did that in a clockwise. Motion. That's just a good habit to get into because if you're doing it on threaded fittings.
