For a standard kitchen sink shutoff valve, you need a 3/8-by-3/8-by-1/4-inch Add-A-Tee. You also need a 1/4-inch flex water supply tube that is long enough to run from the Add-A-Tee to the refrigerator, plus several feet so you can pull out the fridge without yanking on the water line.
How do I add a shut off valve to my refrigerator water line?
Quote from the video:
Quote from Youtube video: Go bring the compression fitting up and screws right into the valve. Itself. Okay then you take your half inch wrench. And you have to tighten that you don't want to over tighten it obviously.
How do you install a quarter shut off valve?
Quote from the video:
Quote from Youtube video: So you want to take the compression nut slide it on you're going to slide the brass washer in place like that back on there now we're going to take our shutoff valve.
How do you hook up a shut off valve?
Quote from the video:
Quote from Youtube video: And then we install these caps and check for leaks to show you how they work. Okay with your main water valve shut off and draining the extra water in the system from the lowest point in your home.
What can I use instead of a saddle valve?
A similarly DIY-friendly but more reliable alternative to a saddle valve is a push-fit tee connector designed for ice makers and water dispensers. You install these by cutting out a short section of pipe and installing the tee right into the water line, then adding the small supply line leading to the appliance.
What size is refrigerator water line fitting?
The tubing should have a diameter of 1/4-inch and can be copper line, braided steel line or plastic tubing. Many professionals prefer copper line, but plastic tubing is commonly sold as part of ice maker installation kits.
How do you install a shut-off valve on an existing PVC pipe?
Quote from the video:
Quote from Youtube video: Use these types of pipe cutters. If you're working on CPVC. A like I am and cut the pipe as close as possible to the old shutoff valve next use sandpaper and sand a little bit to remove debris.
How do you install a sharkbite shut-off valve on a PEX?
Quote from the video:
Quote from Youtube video: Make sure to leave a minimum of one inch of pipe to insert the sharkbite stop valve onto the stub out be sure the pipe is free of scratches. And debris.
Are quarter turn valves better?
Yes, ball valves or quarter turn valves tend to be more reliable than globe valves. Globe valves require a washer and a tight friction fit between the seat and washer, and if either of these wear out (which they do over time), leaks start. Ball valves are much simpler in construction.
How do you install a shut-off valve on an existing copper water line?
Quote from the video:
Quote from Youtube video: We're going to put the ferrule over the top of it and make sure the ferrule slides all the way down the valve then sits on top of that and you want to make sure that the valve is all the way.
How do you install a sharkbite shut-off valve on a copper pipe?
Quote from the video:
Quote from Youtube video: Today first if you have copper pipes first thing you want to do once you have the old valve. Off is clean up the edges with some sandpaper fairly simple so we're going to grab the shark bite.
How do you cap off a copper water line to a refrigerator?
Quote from the video:
Quote from Youtube video: Set it right inside the pipe. And just press it on. And you hear a definite click and you can feel it hit back in here.
Why you should never use a saddle valve?
Quote from the video:
Quote from Youtube video: Can deform that pipe and take it out of round. That. Also could lead to turbulence of the water inside that pipe which could break down any nearby soldering connections on the pipe too.
Can saddle valves be shut off?
Saddle valves are self-tapping devices. Once mounted on a line, with the included rubber seal in place, all that is required is to turn the valve clockwise until it pierces the water line. When the valve handle can no longer be turned, it is done tapping the pipe. Turning the handle counter-clockwise opens the valve.
Are saddle valves illegal?
Answer. Most state and local codes prohibit the use of a saddle valve, also known as a piercing saddle valve, saddle tap or needle valve, consisting of a clamp that punctures a hole in an existing water intake pipe. It is a shortcut used instead of installing a more permanent and secure connection.
How do you install a saddle valve?
Quote from the video:
Quote from Youtube video: The sample the settle melt like it's laid out here little rubber piece fits the channel of the pipe hug the pipe the the actual saddle valve is going to get inserted. Into the saddle. And twist.
What is a self tapping saddle valve?
Quote from the video:
Quote from Youtube video: And this is self piercing it has a needle valve that is going to cut its own hole into the copper tubing. And then as we unscrew this allow the flow of water to go into our humidifier.
Are saddle valves any good?
Most of them don’t leak, but they have a much higher chance of leaking than a properly installed water valve. My advice is to not use saddle valves. When installing an ice maker or whole-house humidifier, tap off of an existing water line with a proper tee fitting and have a proper shutoff valve installed.
How do you tap into an existing water line?
Quote from the video:
Quote from Youtube video: The next thing I'm going to do is using the hacksaw. Make two cuts one here. And another one about an inch. Over. Measure about one inch from the end and you're going to cut this off right over.
How do you put a saddle valve on a PVC pipe?
Quote from the video:
Quote from Youtube video: And push it inside the saddle valve here with the needle. Open who's gonna feed that needle into the hole. Should feel like kind of make a connection here oh there's more going down my sleeve.
